MerCruiser 496 MAG Bravo User Manual Download Page 32

Page: 32 / 146

Section 2 - Getting to Know Your Power Package

Page 24

90-864839061 NOVEMBER 2006

Your power package may be connected to the Mercury SC5000 SmartCraft System View

display. The display monitors and reports information ranging from basic operating data to

engine alarm data.
The SC5000 System View Display is a comprehensive boat information center. System

View allows the boat operator to receive a wealth of critical operational information,

displayed clearly and instantly at the helm on the LCD display. The System View

continuously monitors and reports information ranging from basic operating data to detailed

vessel environment information. System View displays water temperature and depth,

engine trim status, boat speed, steering angle, system preventive maintenance reminders

and systems diagnostics. System View also can be fully integrated with the boat's GPS, if

equipped, to provide up to the minute location, course, speed, and fuel‑to‑destination

information.
When a problem is detected with the engine or system, the System View will alert the

operator to the potential problem by displaying the alarm message in the information

window, located at the bottom of the view screen.
If the problem can cause immediate engine damage, the Engine Guardian System will

respond to the problem by limiting engine power. Immediately reduce throttle speed to idle.

Refer to the System View Operation Manual for further explanation of the problem and the

correct action to take.

Digital Gauges

A Mercury SmartCraft System instrument package can be purchased for this product. A

few of the functions the instrument package will display are engine RPM, coolant

temperature, oil pressure, battery voltage, fuel consumption and engine operating hours.
The SmartCraft Instrument package will also aid in Engine Guardian diagnostics. The

SmartCraft Instrument package will display critical engine alarm data and potential

problems.
Refer to the manual with your gauge package for the warning functions monitored and

basic operation of the SmartCraft Instrument package.

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands