MerCruiser 496 MAG Bravo User Manual Download Page 16

Page: 16 / 146

Section 1 - Warranty

Page 8

90-864839061 NOVEMBER 2006

This limited warranty does not cover the following:

•

Electrical system corrosion

•

Corrosion resulting from damage

•

Corrosion that causes purely cosmetic damage

•

Abuse or improper service

•

Corrosion to accessories, instruments, and steering systems

•

Corrosion to a factory‑installed jet drive unit

•

Damage due to marine growth

•

Replacement parts (parts purchased by the customer)

•

Product sold with less than a one‑year limited product warranty

•

Products used in a commercial application. Commercial use is defined as any work or employment

related use of the product, or any use of the product which generates income, for any part of warranty

period, even if the product is only occasionally used for such purposes.

Global Warranty Charts

IMPORTANT: Please refer to

www.mercurymarine.com/global_warranty

for the most

currant Global Warranty Charts.

Consumer Application Warranty Chart

Consumer Application: Standard Factory Limited Warranty by Region & Boat Brand

Limited Corrosion

Warranty

Non-Certified Boat Brand

Certified Boat Brand

All Boat Brands

Region

Standard SeaCore Horizon

6.2

Scorpion

Standard SeaCore Horizon

6.2

Scorpion

Standard

and Horizon

SeaCore

USA and
Canada

1 year

3 years 3 years

3 years

2 years

4 years 4 years

4 years

3 years

4 years

Latin
America

1 year

3 years

1 year

2 years

4 years 2 years

2 years

3 years

4 years

Mexico

1 year

3 years

1 year

4 years

1 year

4 years

Europe

2 years

3 years 2 years

2 years

3 years

4 years 3 years

3 years

4 years

Japan

1 year

Australia and
New Zealand

2 years

3 years 3 years

3 years all

Tow Sports

2 years

3 years 3 years

3 years all

Tow Sports

3 years

4 years

South Pacific

1 year

3 years

1 year

3 years

1 year

3 years

4 years

Asia
(excluding
Japan, South
Pacific,
Australia,
New Zealand)

2 years

2 years 2 years

3 years all

Tow Sports

2 years

2 years 2 years

3 years all

Tow Sports

2 years

NOTE: In regions where the Certified Boat Builder program is not applicable, the regular warranty always applies.
NOTE: In regions where TBD (To Be Determined) is listed, check with your local dealer for warranty length and conditions.

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands