MerCruiser 496 MAG Bravo User Manual Download Page 36

Page: 36 / 146

Section 2 - Getting to Know Your Power Package

Page 28

90-864839061 NOVEMBER 2006

Zero Effort Features

5656

a -

Shift ever

b -

Throttle lever

c -

Trim/tilt switch

Shift Lever -

Shift functions are controlled by the movement of the shift lever. Shift into

reverse by moving the shift lever to its aft position. Shift into neutral by moving the shift

lever to its center position. Shift into forward by moving the shift lever to its forward position.

Throttle Lever -

Throttle functions are controlled by the movement of the throttle lever.

Increase the RPM by moving the throttle lever forward. Achieve Wide Open Throttle (WOT)

by placing the throttle lever in its full forward position. Decrease RPM by moving the throttle

lever back. Achieve minimum RPM (idle) by placing the throttle lever in its full aft position.

Trim/Tilt Switch -

Refer to

Power Trim

Remote Controls (DTS Models)

Remote Controls

IMPORTANT: Your boat must be equipped with a Mercury Marine electronic remote

control. Start in gear protection is provided by this control system and prevents the engine

from starting when the control is actuated in forward or reverse. Refer to the Mercury

Precision Parts/Quicksilver Accessories Guide.
The Digital Throttle and Shift System (DTS) required to operate this engine package

provides start and stop functions, throttle control, shift control, start in gear protection, and

emergency lanyard stop functions. The DTS system works with specialized helm

components such as a command module kit and electronic remote control. Consult your

dealer for a description and/or demonstration of your remote control.

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands