MerCruiser 496 MAG Bravo User Manual Download Page 99

Page: 99 / 146

Section 5 - Maintenance

90-864839061 NOVEMBER 2006

Page 91

Tube Ref No.

Description

Where Used

Part No.

U-joint and Gimbal Bearing

Grease

Transom end grease fitting,

engine end grease fitting,

driveshaft grease fittings

92-802870A1

Propellers

Propeller Repair

Some damaged propellers can be repaired. Contact your authorized Mercury MerCruiser

dealer.

Bravo Sterndrive Propeller Removal

WARNING

Avoid Injury: Remote Control must be in neutral and ignition key removed from switch

before removing and/or installing propeller.

WARNING

A rotating propeller can cause injury. Place a block of wood between the anti‑ventilation

plate and the propeller to protect hands from the propeller blades, and to prevent the

propeller from rotating when removing or installing the propeller nut.

BRAVO ONE MODELS

NOTE: Bravo One XR models do not use the tab washer.

1. If Equipped, straighten the bent tabs of the tab washer on the propeller shaft.

4750

a -

Prop

b -

Tab washer

c -

Drive sleeve adapter

d -

Tab bent down

e -

Propeller nut

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands