MerCruiser 496 MAG Bravo User Manual Download Page 128

Page: 128 / 146

Section 6 - Storage

Page 120

90-864839061 NOVEMBER 2006

CAUTION

Excess water in the bilge can damage the engine or cause the boat to sink. When the

drain system is open, excess water can enter the bilge. Do not operate the engine with

the drain system open.

IMPORTANT: Only drain the seawater section of the closed cooling system.
IMPORTANT: The boat must be as level as possible to ensure complete draining of the

cooling system.
Your power package is equipped with a drain system. Refer to

Drain System

Identification

to determine which instructions apply to your power package.

IMPORTANT: The engine must not be operating at any point during the draining procedure.

Drain System Identification

AIR ACTUATED SINGLE POINT DRAIN SYSTEM

8294

a -

Actuator fitting

b -

Green indicators

c -

Manual release valve

17254

a -

Port side drain location

b -

Starboard side drain location

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands