MerCruiser 496 MAG Bravo User Manual Download Page 57

Page: 57 / 146

Section 3 - On The Water

90-864839061 NOVEMBER 2006

Page 49

Freezing Temperature Operation

IMPORTANT: If the boat is operated during periods of freezing temperature, precautions

must be taken to prevent freeze damage to the power package. Damage caused by

freezing is not covered by Mercury MerCruiser Limited Warranty.

Drain Plug and Bilge Pump

The engine compartment in your boat is a natural place for water to collect. For this reason,

boats are normally equipped with a drain plug and/or a bilge pump. It is very important to

check these items on a regular basis to ensure that the water level does not come into

contact with your power package. Components on your engine will be damaged if

submerged. Damage caused by submersion is not covered by the Mercury MerCruiser

Limited Warranty.

Basic Boat Operation (DTS Models)

Launching and Boat Operation

IMPORTANT: Install bilge drain plug prior to launching boat.

CAUTION

To avoid possible ingestion of water that can damage engine components, do not turn

the ignition key off when the engine is above idle speed. When launching your boat from

a steep ramp, enter the water slowly. Do not use the lanyard stop switch to shut off the

engine above idle speed. When coming off plane, if a large following wave may roll over

the boat's transom, apply a short, light burst of throttle to minimize the wave action against

the stern of the boat. Do not come off plane quickly and then shut off the engine. Also

avoid shifting into reverse while on plane.

OPERATION CHART

Operation Chart

BEFORE STARTING

AFTER STARTING

WHILE UNDERWAY

AFTER STOPPING

Install bilge drain plug.

Observe all gauges to

check condition of

engine. If not normal, stop

engine.

Observe all gauges to

check condition of engine. If

not normal, stop engine.

Turn ignition key to the

"OFF" position.

Open engine hatch.

Check for fuel, oil, water,

fluid and exhaust leaks.

Listen for the audio alarm. Turn battery switch to the

"OFF" position.

Turn battery switch on.

Check shift and throttle

control operation.

Close fuel shut off valve.

Operate bilge blowers.

Check steering operation.

Close seacock, if

equipped.

Open fuel shut off valve.

Flush cooling system if in

saltwater.

Open seacock, if

equipped.

Drain bilge.

Close the drain system.
Place sterndrive unit in

full down/in position.
Check the engine oil.
Perform all other checks

specified by your dealer

and/or boat builder.

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands