MerCruiser 496 MAG Bravo User Manual Download Page 134 | Manualshive

Page: 134 / 146

background image

Section 6 - Storage

Page 126

90-864839061 NOVEMBER 2006

BOAT OUT OF THE WATER

NOTE: Use this procedure if the air actuated single point drain system fails.
NOTE: It may be necessary to lift, bend, or lower hoses to allow water to completely drain

when hoses are disconnected.

1. Place the boat on a lever surface to ensure complete draining of the system.
2. Remove two blue drain plugs from the seawater pickup pump (front, starboard side).

a

17255

a

a -

Blue drain plug locations

3. Verify that water is draining from each opening.
4. Allow the system to drain for a minimum of five minutes. Mercury MerCruiser

recommends leaving the drain system open while transporting the boat or while

performing other maintenance to ensure that all water is drained.

5. For DTS engines, pull the lanyard stop switch (if equipped), or disable the ignition circuit

by pulling the fuse marked "CD".

6. Crank the engine over slightly with starter motor to purge any water trapped in the

seawater pickup pump. Do not allow the engine to start.

7. Prior to launching the boat or starting the engine, close the drain system by installing

the two blue drain plugs.

Draining the Sterndrive

NOTE: This procedure is needed only for salty, brackish, mineral laden, or polluted water

applications; and for freezing temperatures or extended storage.

«
...
132
133
134
135
136
...
»

Summary of Contents for 496 MAG Bravo



















































































































































Reviews:

No comments

Related manuals for 496 MAG Bravo

Brand: Danfoss Pages: 28

Brand: Kohler Pages: 12

Brand: B&R Pages: 8

Brand: Vedeneyev Pages: 381

Smart Motor SM23166MT

Brand: MOOG ANIMATICS Pages: 32

COMBIFLUX FP 314 PVDF

Brand: Flux Pages: 28

Brand: Applied Motion Products Pages: 2

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 90

Brand: Yamaha Pages: 110

Brand: Yamaha Pages: 110

Brand: Yamaha Pages: 232

Brand: Yamaha Pages: 305

Brand: Yamaha Pages: 307

Brand: Yamaha Pages: 372

Brand: Yamaha Pages: 444

Brand: BAFANG Pages: 6

Brand: Lycoming Pages: 194

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands