background image

It is of vital importance, before attempting to operate 
your  engine,  to  read  the  general 

'SAFETY 

INSTRUCTIONS  AND  WARNINGS'  section  on 
pages 2-6 of this booklet and to strictly adhere to the 
advice contained therein.

Also,  please  study  the  entire  contents  of  this 
instruction  manual,  so  as  to  familiarize  yourself 
with the controls and other features of the engine.

Keep these instructions in a safe place so that you 
may readily refer to them whenever necessary.

It  is  suggested  that  any  instructions  supplied  with 
the  aircraft,  radio  control  equipment,  etc.,  are 
accessible for checking at the same time.

1

CONTENTS

SAFETY INSTRUCTIONS AND WARNINGS ABOUT 
YOUR O.S. ENGINE

ENIGNE CONSTRUCTION,
NOTES WHEN APPLYING AN ELECTRIC STARTER

INTRODUCTION, INSTALLATION

BEFORE STARTING

ADVICE ON SELECTION OF FUEL, GLOW 
PLUG & PROPELLER

STARTING THE ENGINE,
RUNNING-IN (Breaking-in)

TROUBLE SHOOTING WHEN 
THE ENGINE FAILS TO START

CARE AND MAINTENANCE

10LA ENGINE EXPLODED VIEW &
PARTS LIST 

15LA ENGINE EXPLODED VIEW 
& PARTS LIST 

25LA ENGINE EXPLODED VIEW 
& PARTS LIST 

CARBURETTOR EXPLODED 
VIEW & PARTS LIST

O.S. GENUINE PARTS & ACCESSORIES

2-6

7-8

9-12

13-15

16-17

18-29

29-30

31

32-33

34-35

36-37

38-39

CARBURETTOR

15/25LA CARBURETTOR 
AIR-BLEED ADJUSTMENT

40-41

42-44

45-46

THREE VIEW DRAWING

47-48

Summary of Contents for MAX-10LA


























Reviews: