Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download

Page: 155 / 171

Accessories

155

Slow moving vehicle sign

A slow moving vehicle (SMV) sign is a reflective orange triangle with
a red border that warns other road users that the vehicle displaying the
sign is travelling at 40 km/h (25 mph) or less.

Hardened vanes

In case of intensive spreading of fertilizer with high roughness,
interchanging vane positions on the disc is sometimes not enough.



In this regard, see the paragraph »Even wear of the vanes« on
page 43.

A set of hardened vanes then considerably increases the life span.

Set of vanes 330-330-330

Set of vanes for spreading large working widths (up to 177 feet).

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Related manuals for Exacta-TL-GEOSPREAD GS3

Brands by name

Popular brands

Kverneland Exacta-TL-GEOSPREAD GS3, Operator'S Manual

Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Related manuals for Exacta-TL-GEOSPREAD GS3

Brands by name

Popular brands