Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download

Page: 132 / 171

Maintenance

132

Lubricating points

All lubricating nipples of the machine can be filled with a universal
grease type.



See »Oil and grease content« on page 130.



See »Maintenance intervals« on page 131.

Coupling shaft with quick

lock



Lubricate the 4 nipples.



Check the condition of the protection sleeves and the check
chains.



Replace them if damaged.

Discharge bushings

The discharge bushings are attached lower down to the agitator axle
and have 2 grease nipples.



Open the discharge bushings



Please refer to the software instruction manual.



Turn the spreading disc by hand until both grease nipples are visi-
ble.



Grease the 2 nipples of both discharge bushings.

Actuators

The actuators are provided with 1 grease nipple.



Grease the nipple of all four actuators.

Grease nipples

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Related manuals for Exacta-TL-GEOSPREAD GS3

Brands by name

Popular brands

Kverneland Exacta-TL-GEOSPREAD GS3, Operator'S Manual

Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Related manuals for Exacta-TL-GEOSPREAD GS3

Brands by name

Popular brands