manualshive.com logo in svg

Kverneland Exacta-TL-GEOSPREAD GS3, Operator'S Manual

Share
Download
Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download Page 108

Use in the field

108

Border spreading plate

Set the field boundary as close as possible to the left while driving 
along the field boundary, to spread right down to the border with 
the border spreading plate.

Fill the headland through to half the working width without the 
border spreading plate with the correct dosage selected to make 
an additional pass.

See »One-sided boundary spreading with the border spreading 
plate« on page 111.

Fill the field with injections on your sprayer tramline defined 
previously.

The GEOCONTROL will itself determine the correct start/stop 
moment while approaching and turning from the spread headland.

Spreading without GEOCONTROL headland:

Stop spreading by closing the dosing units of the machine when 
you are half a working width from the end of the land.

Let the spreading discs turns and do not switch off the PTO shaft.

Open the dosing units again at one and a half the working width of 
the field edge.

Finally, spread the site edges with the ExactLine.

See paragraph »Border spreading« on page 111.

With one-sided border spreading (situation B)

Closing dosing units

Opening dosing units

Minimum

Border spreading

Border spreading

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands