manualshive.com logo in svg

Kverneland Exacta-TL-GEOSPREAD GS3, Operator'S Manual

Share
Download
Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download Page 114

Use in the field

114

Driving pattern

Two different driving patterns can be used, depending on the situation 
on your land.

I

NDICATION

Only drive counter-clockwise (to the left) when using the border 
spreading plate and ExactLine.

Working from the sprayer tramlines (situation A):

Drive the first path with the middle of the tractor about 7 ft. from the 
field edge. Decrease the PTO shaft rpm to 75%.

Remove the border spreading plate at the end of the first path, but 
leave the right spreading disc disconnected and the dosing units 
closed,

see the methods above.

Increase the PTO shaft rpm to 100% again.

Drive down the second path in the first sprayer tramline.

After the second operation, link up the right spreading disc drive 
again.

Open the right spreading disc dosing unit by pressing the open 
key.

Working without sprayer tramlines (situation B):

Drive the first path with the middle of the tractor about 7 ft. from the 
field edge. Decrease the PTO shaft rpm to 75%.

Remove the border spreading plate after the first operation.

Reconnect the drive of the right spreading disc.

Open the right spreading disc dosing unit by pressing the open 
key.

Drive up the second line 1 working width from the field edge (X ft.). 
Maintain the distance with the field edge carefully by using pickets, 
for instance.

75 cm

29½ “

75 cm

29½ “

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands