manualshive.com logo in svg

Kverneland Exacta-TL-GEOSPREAD GS3, Operator'S Manual

Share
Download
Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download Page 54

Connecting to the tractor

54

Selecting linkage pin 

height

There is an option of two tension levels, depending on the height of 
the crop. The lower hitch points are used if the maximum lifting height 
of the tractor is not sufficient to ensure that the spreading height is 75 
cm/29.5 in above the crop.
The low hitch points are also used when fertilising high crops, which is 
known as top dressing.
For further adjustments with top dressing, see

paragraph »Spreading height« on page 100.

\ 

WARNING

Check the coupling shaft

Check the following points before the PTO shaft is attached. Has 
the coupling shaft:

•

no damage, including the protection sleeves?

•

are there sufficient lubricants as prescribed?

•

is the prescribed overlap of the coupling shaft halves and pro-
tection sleeves, both in transport and in operating position?

•

Are the protection sleeves attached with chains to a fixed point 
to guard against turning?

An unsafe or improperly mounted coupling shaft could lead to 
serious or deadly injury.
If the coupling shaft does not comply with the points mentioned 
above, it must be replaced before using the machine.

Linkage pin high

Linkage pin low

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands