manualshive.com logo in svg

Kverneland Exacta-TL-GEOSPREAD GS3, Operator'S Manual

Share
Download
Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download Page 70

To be done before spreading

70

Dosing setting

The dosing setting to be set can be:

•

Read from the relevant spreading chart if a lower application rate 
is to be used whereby the fine application kit is used and 

Fine 

application kit

 is indicated under the heading in the spreading 

chart:

 

yes

.

Determine an application rate not given as described in para-
graph »Discharge point«from page 67.

•

Calculate using the relevant spreading chart if a lower application 
rate is to be used whereby the fine application kit is indeed used 
and 

Fine application kit 

is indicated under the heading in the 

spreading chart: 

no

.

Calculation

As 2 of the 3 dosing openings are closed the flowrate of the remaining 
dosing opening should be three times as much in order to obtain an 
even application rate.

Read the 

Dosing Setting, Discharge Point and Flowrate 

from the 

spreading chart. Calculate the flowrate with the formula given 
below as required.

If the selected application rate or driving speed is not indicated in the 
spreading chart the required flowrate can also be calculated as 
follows:

Use the letter given for setting the discharge point in the line of the 
spreading chart that most closely resembling the calculated flowrate.

Multiply the flowrate (given in the 

lbs/min 

column or calculated) 

with a factor of 3.

Select the closest flowrate for the whole spreader in the 

lbs/min

 

column.

Read off the relevant dosing setting or estimate it as closely as 
possible. 

N

OTE

Do not use the discharge point indicated 

there

.

Setting the spreader

Set the given discharge point as described

in paragraph »Discharge point« on page 67.

Enter the dosing setting in the control system and determine the 
relevant flowrate by means of a manual calibration test, as 
described in the following paragraph.

See also the example in paragraph »Constant application rate« on 
page 68.

500

flowrate required (lbs/min) =

Working width (ft) x Driving speed (mph) x Application rate (lbs/acre)

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands