Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download Page 107

Page: 107 / 171

Use in the field

107

Working method on the

headland

The driving pattern that you use, in other words how you must turn on
the headland, depends on your border spreading method.

•

spreading the border from the sprayer tramline with ExactLine,
one-sided border spreading with additional room with the border
spreading plate (situation A), or

•

border spreading by closing off one disc and using a border
spreading plate (situation B).

Do the following when spreading the headland:

For boundary track spreading from the sprayer tramline (Exact-
Line and situation A)

GEOCONTROL headland function

ExactLine



Begin with creating the field boundary where you spread on edges
with the ExactLine while driving to the left through the first sprayer
tramline.



Make a second round with the ExactLine switched off for a double
headland, if required.



Fill the field with injections on your sprayer tramline defined
previously.

The GEOCONTROL will itself determine the correct start/stop
moment while approaching and turning from the spread headland.

Closing dosage units
by GEOCONTROL

Geo

Opening dosing units
by GEOCONTROL

Border spreading

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Related manuals for Exacta-TL-GEOSPREAD GS3

Brands by name

Popular brands

Kverneland Exacta-TL-GEOSPREAD GS3, Operator'S Manual

Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Related manuals for Exacta-TL-GEOSPREAD GS3

Brands by name

Popular brands