Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download Page 125

Page: 125 / 171

Storing the machine

125

Disconnecting the

machine

Proceed as follows to store the machine in stable condition for a
shorter or longer period.



switch off the pto shaft;



Check that the ExactLine hydraulic hose tap is closed.



Take the pressure off the hydraulic system.



Place the machine on a stable, level base.



switch the electronic control system off,



Engage the parking brake of the tractor.



Adjust the length of the top link in such a way that it is no longer
live.



Release the top link by undoing the release rope from the catch
hooks and pulling the top link up.



Release the lower links by undoing the release ropes from the
catch hooks and lowering the power lift as far as possible.

WARNING

Disconnect safely
You may only disconnect the machine when

•

all parts are in a safe condition,

•

your immediate surroundings are safe,

•

the hopper is empty.

Work carefully:

•

check the environment (children!) and ensure that nobody is in
the vicinity of the tractor or the machine.

•

wear safety gloves and shoes,

•

the machine or parking support must only be placed on a flat,
firm surface,

•

never stand between the tractor and machine while the power
lift is operated externally while disconnecting the machine,
Using the power lift entails the risk of accidents by crushing or
jack-knifing.

•

operate the power lift slowly and carefully,

•

the power lift during disconnection must be placed in such a
position that accidental release or lowering would be elimi-
nated,

•

sufficient distance must be maintained between parts (e.g.
parking support) that rest on the ground.

Working unsafely could cause serious injuries.

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Brands by name

Popular brands

Kverneland Exacta-TL-GEOSPREAD GS3, Operator'S Manual

Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Brands by name

Popular brands