Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download

Page: 44 / 171

Before first use

Set of vanes 330-330-330

A set of vanes is available for larger working widths.
The set consists of two different vanes 4x with an angle of 5º and 8x
with an angle of 10º



Grease the threaded rods of the vanes.



Place the vanes with a 5° (B) angle in the positions before the fixed
vane



Place the vanes with a 10° (A) angle in the other positions.



Fasten the lock nuts (37 ft.lb)

Pellet sieve

This sieve can be used when spreading with pellets.

Attachment for sieve

opening

This tool can be used to open the sieves.
The attachment comes standard with the machine and is located on
the left wing of the frame.

fixed vane

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Related manuals for Exacta-TL-GEOSPREAD GS3

Brands by name

Popular brands

Kverneland Exacta-TL-GEOSPREAD GS3, Operator'S Manual

Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Related manuals for Exacta-TL-GEOSPREAD GS3

Brands by name

Popular brands