Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download Page 48

Page: 48 / 171

Before first use

Hydraulic border spreading

plate



Fit the frame to the machine; see also the spare parts manual.



Fit the laminated box to the frame.

Connect the position sensor in the electronic box on the spreader:



Also see the spare parts manual for the correct assembly.



see »Position indicator«on page 48.

Border spreading plate

The border spreading plate is used to spread the sides while moving
alongside the field edge.



Mount the support for the border spreading plate.



Mount the transport support for the border spreading plate, see
also the parts sheet.



See also »Position of the border spreading plate« on page 88.

Position indicator

A sensor is available with these accessories to be able to read in the
tractor cabin whether the ExactLine(s) and/or the hydraulic border
spreading plate are in the working position.
This is connected to the machine electronics.

Frame

Sensor

Laminated box

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Related manuals for Exacta-TL-GEOSPREAD GS3

Brands by name

Popular brands

Kverneland Exacta-TL-GEOSPREAD GS3, Operator'S Manual

Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Related manuals for Exacta-TL-GEOSPREAD GS3

Brands by name

Popular brands