Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download Page 45

Page: 45 / 171

Before first use

Hydraulic drive

A hydraulic drive is available to power the machine without PTO shaft.



The tractor must have a minimum oil yield of 13 gal/min (2320 psi).



The maximum yield is 550 lbs/min in combination with the 330-
330-330 set of vanes.



The set is supplied with a mould for easy alignment.



Please refer to the accompanying installation instructions for
correct installation.

Mud guards

A set of mud guards can be mounted to protect the machine against
being dirtied by the tractor wheels.



Also see the spare parts manual for the correct assembly.

Step

For safely performing an inspection in the cover, a step (optional ex-
tras) is mounted to the left and/or right of the hopper. Use the step by
pressing the button, turning it a quarter rotation and folding out the
step downwards.



Also see the spare parts manual for the correct assembly.

Hydraulic drive

step

button

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Brands by name

Popular brands

Kverneland Exacta-TL-GEOSPREAD GS3, Operator'S Manual

Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Brands by name

Popular brands