Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download Page 47 | Manualshive

Page: 47 / 171

background image

Before first use

47

Coupling shaft connection

point

The working width of the machine is mostly determined by the RPM of
the spreading disc. The speed of the spreading disc depends on the
speed of the PTO shaft and the chosen connection from the coupling
shaft.



See also paragraph »Working width« on page 66.

I

NDICATION

If the (online) spreading chart specifies another coupling shaft
connection point or spreading disc speed, use the values from the
(online) spreading chart.



See also paragraph »Working width« on page 66.

ExactLine

The ExactLine is used for border spreading from the sprayer tramline.
The ExactLine is available in a right and a left version.



Also refer to the instruction sheet for correct installation.

Fast/hare connection point

Slow/tortoise connection point

«
...
45
46
47
48
49
...
»

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Reviews:

No comments

Related manuals for Exacta-TL-GEOSPREAD GS3

Brand: Calistair Pages: 44

Brand: Oemtools Pages: 4

Brand: Modulate Pages: 2

Brand: Panta Safe Light Pages: 2

Brand: Calrec Pages: 70

Brand: Yamaha Pages: 46

Brand: ZacUrate Pages: 2

Brand: ZacUrate Pages: 2

Brand: LSI Pages: 24

Brand: Kelso Pages: 21

Brand: DC Med Pages: 2

Brand: EHEIM classic Pages: 128

MINOR 2000 G.E.

Brand: Oscartielle Pages: 44

Brand: Poulan Pro Pages: 18

Brand: Bondura Pages: 10

Brand: Beaumont Pages: 7

Brand: Hill-Rom Pages: 28

Brand: Game Winner Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands