Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download

Page: 149 / 171

Maintenance

149



Open the sieves and lock them.



Remove the agitator from the agitator axle.



Support the fertilizer bearing ring through a dosing opening so that
it will not drop.



Remove the 3 fastening bolts from the seal rings.



Remove the metal seal rings.



Check the condition of the agitator axle.



Replace the fertilizer sealing ring.



Put the metal seal rings back in position.



Put the 3 fastening bolts back in place.

You can let go of the bearing ring after the first fastening bolt has been
put back in place.



Put the agitator back into the agitator axle.

Check the connections as described in



paragraph »Checking and setting the dosing mechanism« on page
141.

agitator axle

Seal ring

agitator axle

Bolt holes

Plastic sealer rings

agitator

agitator axle

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Related manuals for Exacta-TL-GEOSPREAD GS3

Brands by name

Popular brands

Kverneland Exacta-TL-GEOSPREAD GS3, Operator'S Manual

Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Related manuals for Exacta-TL-GEOSPREAD GS3

Brands by name

Popular brands