manualshive.com logo in svg

Kverneland Exacta-TL-GEOSPREAD GS3, Operator'S Manual

Share
Download
Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download Page 111

Use in the field

111

Border spreading

Spreading fertiliser up to the border of the property requires concen-
tration. On the one hand you want to achieve maximum cover to the 
field edge to ensure a good crop, while on the other hand you want to 
minimise the loss over the field edge.
The spreader has 2 different functions and accessories to cater for 
border spreading

•

one-sided boundary spreading with border spreading plate or hy-
draulic border spreading plate,

•

boundary track spreading with ExactLine.

When one-sided boundary spreading, drive with the tractor along the 
field edge and spread from the border inwards. With boundary track 
spreading, drive down the first sprayer tramline from the field edge 
and spray in the direction of the border.

I

NDICATION

We advise you to spread the site first before you spread the borders. 
During border spreading, the control system does not perform any au-
tomatic calibration, so it cannot accurately determine the correct dos-
ing setting for the required application rate. Consequently, the 
application rate can deviate from the required application rate during 
border spreading. By spreading the field first, the control system can 
determine the correct dosing setting and thus spread at the correct ap-
plication rate, also during border spreading.

One-sided boundary 

spreading with the border 

spreading plate

Operation

Drive along the field edge when one-sided boundary spreading and 
send the flow of fertiliser granules with the hydraulic border spreading 
plate (optional extra). The working width on the side of the field edge 
can be adjusted by changing the (hydraulic) border spreading plate 
(optional extra).

Direction 

X

 (

1

)

(environmental 
setting)

Spread less to the field edge. 
This will decrease the loss over the field edge, 
but the cover will not be as good

Direction 

Y

 (

9

)

(yield setting)

Spread more to the field edge. 
Cover is better, but the loss is greater

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands