Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download | Manualshive

Page: 134 / 171

background image

Maintenance

134

Apply oil

The following parts only function well if they are provided with
sufficient oil. Check this regularly.

Connectors

The connectors between the central gearbox and the spreading disc
gearboxes are used with border spreading, with a calibration test and
when checking the spreading pattern with the tray test. Disconnect
one of the connectors from the spreading discs.



Apply a suitable lubricant to the drive axles and connectors.

Oiling the connectors will prevent them from corroding and becoming
difficult to use.

Connectors

«
...
132
133
134
135
136
...
»

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Reviews:

No comments

Related manuals for Exacta-TL-GEOSPREAD GS3

Brand: Omnia Pages: 8

Brand: Tate Pages: 7

Brand: Tate Pages: 5

BioHarmonex BH4

Brand: Calivita Pages: 38

Brand: CAIRE Pages: 91

PowerXL DX-NET-ETHERNET2-2

Brand: Eaton Pages: 48

Power Xpert C445

Brand: Eaton Pages: 2

Brand: Taurus Pages: 24

Brand: Mackie Pages: 18

Brand: Mackie Pages: 2

Brand: Mackie Pages: 8

Brand: Mackie Pages: 7

Brand: NanoVibronix Pages: 2

Brand: NanoVibronix Pages: 32

Shapes Hexagons

Brand: Nanoleaf Pages: 27

Brand: Abbott Pages: 64

Brand: Gako Pages: 22

Brand: ABB Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands