manualshive.com logo in svg

Kverneland Exacta-TL-GEOSPREAD GS3, Operator'S Manual

Share
Download
Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download Page 112

Use in the field

112

The maximum acceptable loss over the field edge is determined by 
environment standards (EN 13739-2). In order to comply with the 
standard the quantity of fertiliser spread beyond the field edge must 
be a maximum of 10% of the quantity distributed in the centre behind 
the spreader (= 100%). Test if the border spreading plate (optional ex-
tra) door de test therefore always before hand as described in

paragraph on page »Testing the spreading pattern of the border 
spreading plate« 86.

paragraph on page »Testing the spreading pattern of the border 
spreading plate« 89.

Working method

Switch the tractor off and remove the keys from the ignition.

Engage the parking brake of the tractor.

Disconnect the right spreading disc by sliding the connector to the 
right. Secure the connector with a lock clip.

Attach the border spreading plate. We recommend that the border 
spreading plate should be mounted with the triangle on the fixing 
plate.

Check that the vanes do not touch the border spreading plate!

Adjust the spreader based on the details given in the spreading 
chart for the desired working width. Use the same settings and 
coupling shaft mounting point as with full field spreading,

See also paragraph »Setting the spreader« on page 64.

Start the tractor again.

Switch the control box on.

Switch the right spreading disc off by pressing close key in the 
main screen. The right dosing unit remains closed.

Engage the PTO shaft. The correct RPM of the spreading discs is 
the value given in the relevant spreading chart less 25%, e.g. 950 
RPM/min. - 25% = 715 RPM/min.

If you want, you can choose to accelerate so that you are driving at 
the same speed as during full field spreading.

The control system will drive the dosing units in such a way that the 
actual application rate is equal to the set application rate through the 
lower PTO shaft RPM.

In the event of spreader failure or stoppage:

Stop spreading immediately!

Disconnect the PTO shaft immediately!

See then paragraph »Failure and stoppage« on page 119.

After border spreading:

Switch on the right spreading disc again by pressing the open key.

Switch the tractor off, remove the key from the ignition and engage 
the parking brake of the tractor.

Remove the border spreading plate.

Reconnect the drive of the right spreading disc.

 X

 Y

border spreading plate in position 
for a working width of 31 - 54 m

Connector

 X

 Y

Border spreading plate, position 
for a working width of 61 -137 m

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands