Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download

Page: 42 / 171

Before first use

Hopper extension

A hopper extension increases the load capacity of the spreading
hopper. All edges consist of:

•

2 long sides,

•

2 short sides,

•

4 corner parts,

•

4 caps,

•

fixing material.



For correct use of the fixing materials, see the spare parts man-
ual.

Hopper cover

The hopper cover must be mounted on top of the hopper or hopper ex-
tension to protect the content against weather or spray.



Also refer to the instruction sheet for correct installation.

Electric hopper cover

The electric hopper cover can be operated from the control box.

The hopper cover must be mounted on top of the hopper extension to
protect the content against weather or spray.



Please also refer to the accompanying installation instructions for
correct installation.



See also »Electric hopper cover« on page 42

A long side

A corner part with a covering baffle

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Related manuals for Exacta-TL-GEOSPREAD GS3

Brands by name

Popular brands

Kverneland Exacta-TL-GEOSPREAD GS3, Operator'S Manual

Search results

Summary of Contents for Exacta-TL-GEOSPREAD GS3

Reviews:

Related manuals for Exacta-TL-GEOSPREAD GS3

Brands by name

Popular brands