Kverneland Exacta-TL-GEOSPREAD GS3 Operator'S Manual Download | Manualshive

Page: 29 / 171

background image

Getting familiar with the machine

29

Boundary track spreading

with the ExactLine

It is possible to spread right up to the border from the first sprayer
tramline with ExactLine (boundary track spreading).
A ExactLine is available for the right and/or the left.

Selecting the pattern for border spreading

It is not possible to completely cover the field border at the application
rate and not have anything go beyond the border. Current
environmental standards only allow for minimal loss over the field
edge.

ExactLine

ExactLine bends the fertilizer granules in such a way that loss over the
edge of the border is restricted to the bare minimum and it provides as
full spreading pattern as possible.
ExactLine has “environment” and “profit” options for precisely
adjusting border spreading.

1/2 Working width

profit setting

ECO setting

H2O setting

Working width

«
...
27
28
29
30
31
...
»

Summary of Contents for Exacta-TL-GEOSPREAD GS3












































































































































































Reviews:

No comments

Related manuals for Exacta-TL-GEOSPREAD GS3

Brand: GE Pages: 24

Brand: Califone Pages: 7

Brand: CALITEK Pages: 16

Brand: LAHTI PRO Pages: 20

Brand: LAHTI PRO Pages: 16

Brand: J&M Pages: 53

Brand: Qazqa Pages: 2

Sportsound SSR-200

Brand: Daktronics Pages: 5

Brand: Haaga Pages: 31

Z9 Commercial Collection System Z9A

Brand: Yazoo/Kees Pages: 3

Z9 Commercial Collection System Z9A

Brand: Yazoo/Kees Pages: 36

Brand: YASKAWA Pages: 1166

Brand: NEBO Pages: 2

BRUTE AFS570010

Brand: KStrong Pages: 8

Brand: Dr.X Works Pages: 14

Brand: Frontier Pages: 16

Brand: Plum Pages: 44

Smartzone PViQ Connectivity System

Brand: Panduit Pages: 179

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands