Krone 870 HDP Original Operating Instructions Download Page 489

Page: 489 / 568

Terminal – menus [Medium Plus/Comfort Plus Electronics]

Alarm messages

8.16

Supplement to Operating Instructions 150000774_00 _en

BiG Pack 870 HDP, BiG Pack 870 HDP XC

Error number

Designation

Icon

522540-19

Timeout of the CAN messages from KMB 1

KMB1

522560-19

Timeout of the CAN messages from force
measurement amplifier 1 (FMA 1)

FMA1

FMI 31: The conditions of the message have been met.

Error number

Designation

Icon

522536-31

Error from the RMC control unit

RMC

522542-31

Error from KMB 1

KMB1

8.16.1.4

General input/output error 521100 - 521299

FMI 3: There is a short circuit or an overvoltage.

Error number

Designation

Icon

521100-3

Voltage group (UB1)

High

521101-3

Voltage group (UB2)

521102-3

Voltage group (UB3)

521103-3

Voltage group (UB4)

521104-3

Voltage group (UB5)

521105-3

Voltage group (UB6)

521107-3

The power supply of the KMC at the UE
connection has an excessively high voltage.

High

FMI 4: There is a cable break/short circuit, general error or undervoltage.

Error number

Designation

Icon

521100-4

Voltage group (UB1)

LOW

521101-4

Voltage group (UB2)

521102-4

Voltage group (UB3)

521103-4

Voltage group (UB4)

521104-4

Voltage group (UB5)

521105-4

Voltage group (UB6)

521107-4

The power supply of the KMC at the UE
connection has an excessively low voltage.

LOW

FMI 5: There is a cable break, general error or overload.

Error number

Designation

Icon

521100-5

Voltage group (UB1)

High

521101-5

Voltage group (UB2)

521102-5

Voltage group (UB3)

521103-5

Voltage group (UB4)

Summary of Contents for 870 HDP

























































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 870 HDP

Reviews:

Krone 870 HDP, Original Operating Instructions, Page: 489 / 568

Search results

Summary of Contents for 870 HDP

Reviews: