manualshive.com logo in svg

Krone 870 HDP, Original Operating Instructions, Page: 168 / 568

Share
Download
Krone 870 HDP Original Operating Instructions Download Page 168

Terminal – Menus [Medium/Comfort Version Electronics]

 

 

168 

 

Pos: 85.108 /Ü berschriften/Ü berschriften 3/K- O/M/M enü 1-2 "Knotersig nal" @ 381\mod_1444113549263_78.docx @ 2751246 @ 3 @ 1 

 

16.6.2 

Menu 1-2 "Knotter signal"  

Pos: 85.109 /BA/Info-C enter /CCI-ISOBUS-T ermi nal/CCI-Bi G Pack/H auptmenüs/H auptmenü 1 Ei nstellungen/M enü 1-2 "Knotersignal" Einführung @ 381\mod_1444113607344_78.docx @ 2751437 @  @ 1 

 

This menu can be used to set whether an acoustic signal is to sound after a knot is tied. 

Pos: 85.110 /BA/Info-C enter /CCI-ISOBUS-T ermi nal/CCI-Bi G Pack/H auptmenüs/H auptmenü 1 Ei nstellungen/M enü 1-2 "Knotersignal" Bild @ 381\mod_1444113722492_78.docx @ 2751468 @  @ 1 

 

CC000097

CC000030_2

1-2

2/2

 

Fig. 109 

Pos: 85.111 /BA/Info-C enter /CCI-ISOBUS-T ermi nal/CCI-Bi G Pack/H auptmenüs/H auptmenü 1 Ei nstellungen/M enü 1-2 "Knotersignal" M enü aufrufen @ 381\mod_1444113795666_78.docx @ 2751499 @  @ 1 

 

Menu 1 "Knotter" has been selected, see chapter Terminal – Menus, "Menu 1 'Knotter'". 

•  To open the menu, press 

. 

The display shows the "Knotter signal" menu. 
 

Pos: 85.112 /BA/Info-C enter /CCI-ISOBUS-T ermi nal/CCI-Bi G Pack/H auptmenüs/H auptmenü 1 Ei nstellungen/M enü 1-2 "Knotersignal" T abell e Gr afi ken @ 381\mod_1444113865880_78.docx @ 2751530 @  @ 1 

 

These modes can be selected: 

Symbol  

Designation  

Explanation 

 

Mode 1/2 

Knotter signal deactivated  After a knot is tied, an acoustic signal 

does not sound. 

 

Mode 2/2 

Knotter signal activated 

After a knot is tied, an acoustic signal 

sounds. 

 

Pos: 85.113 /BA/Info-C enter /CCI-ISOBUS-T ermi nal/Menüs bedienenM odus änder n_Ver weis @ 355\mod_1438325375182_78.docx @ 2648211 @  @ 1 

 

Changing mode 

•  Select and save the mode, see chapter Terminal – Menus, "Changing value". 
 

Pos: 85.114 /BA/Info-C enter /CCI-ISOBUS-T ermi nal/Menüs bedienen/Wi eder kehr ende Symbol e_Ver weis @ 354\mod_1438323278518_78.docx @ 2648185 @  @ 1 

 

Recurring symbols 

•  See chapter Terminal – Menus, "Recurring symbols". 
 

Pos: 85.115 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Summary of Contents for 870 HDP

























































































































































































































































































































































































































































































































































































Reviews:

No comments