manualshive.com logo in svg

Krone 870 HDP, Original Operating Instructions, Page: 267 / 568

Share
Download
Krone 870 HDP Original Operating Instructions Download Page 267

 

Settings

 

267 

 

Pos: 93.62 /BA/Ei nstellungen/Groß packenpresse/Garnrieg el/Garnrieg el well e spannen / entspannen Bi G PAC K 870 HD P b=285 mm @ 271\mod_1402651614865_78.docx @ 2043322 @ 2 @ 1 

 

19.11 

Tensioning/relieving the twine locking shaft   

2

3

1

 

Fig. 188  
The twine locking shaft (1) is tensioned or relieved by means of the spring (2). 

 

Prerequisite: 

–  The knotter gear is in the idle position, see chapter Settings "Adjusting the needle yoke 

brake".  

–  The flywheel brake is applied. 
 

Tensioning the twine locking shaft 

•  To tension the spring (2), tighten the nut (3) until dimension "b" = 285 mm, measured 

between the eyes of the spring. 

 

Relieving the twine locking shaft 

•  To relieve the spring (2), unwind the nut (3) to the thread end of the eyebolt. 
 

Pos: 93.63 /BA/Ei nstellungen/Groß packenpresse/Garnrieg el/Ei nstellung der Knoter well enbremse 20 mm @ 271\mod_1402654053149_78.docx @ 2043441 @ 3 @ 1 

 

19.11.1 

Adjusting the knotter shaft brake  

 

Fig. 189 
•  Tension the springs (1) until dimension a= approx. 20 mm. 

Pos: 93.64 /Layout Module  /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Summary of Contents for 870 HDP

























































































































































































































































































































































































































































































































































































Reviews:

No comments