manualshive.com logo in svg

Krone 870 HDP, Original Operating Instructions, Page: 214 / 568

Share
Download
Krone 870 HDP Original Operating Instructions Download Page 214

Terminal – Menus [Medium/Comfort Version Electronics]

 

 

214 

 

Pos: 85.313 /BA/Info-C enter /Großpackenpresse/Hauptmenüs/Alar mmeldung en/1) Alar mmeldung en Tabelle allgemein A15( 515) - A18(518) HS Baur eihe @ 386\mod_1444922756729_78.docx @ 2770341 @  @ 1 

 

No./symbol 

Possible cause 

Remedy 

A15/515 

High

 

–  Overvoltage 
–  Tractor alternator is defective. 

•  Check the tractor alternator. 

A17/517 

 

–  The CAN connection between 

the job computer and the 

KRONE measurement force 

computer (KMV2) is 

interrupted. 

–  The CAN wiring is defective. 
–  The KRONE moisture 

measurement computer is 

inactive. 

•  Check the CAN wiring. 
•  Replace the KRONE moisture 

measurement computer (RMC). 

A18/518 

 

–  The CAN connection between 

the job computer and the 

KRONE PIC-I01 computer is 

interrupted. 

•  Check the CAN wiring. 
•  Replace the KRONE PIC-I01 

computer. 

 

Pos: 85.314 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Summary of Contents for 870 HDP

























































































































































































































































































































































































































































































































































































Reviews:

No comments