manualshive.com logo in svg

Krone 870 HDP, Original Operating Instructions, Page: 296 / 568

Share
Download
Krone 870 HDP Original Operating Instructions Download Page 296

Settings

 

 

296 

 

Pos: 93.98 /BA/Ei nstellungen/Schneidwer k/Schnittlänge ei nstellen/Voll bestückung/In Abhängigkeit der M esserbestückung i n den M esser kassetten @ 279\mod_1405067044479_78.docx @ 2147647 @  @ 1 

 

Depending on the number of knives in the drawers 

Pos: 93.99 /Layout Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_1342592918145_0.docx @ 1092566 @  @ 1 

 

 

Pos: 93.100 /BA/Wartung/Schneidwer k/M esser wechsel Bild @ 275\mod_1404401306487_78.docx @ 2068091 @  @ 1 

 

5

BPHS0300

3

6

 

Fig. 221 

Pos: 93.101 /BA/Ei nstellungen/Schneidwer k/Schnittl änge einstell en/Vollbestückung/Schni ttlänge ei nstellen T 1 i n Abhängigkeit d er Messer bestückung @ 275\mod_1404470280193_78.docx @ 2069803 @  @ 1 

 

To set different chop lengths using the number of knives in the drawers, a number of knives 

must be removed or inserted. Chop length depending on the number of knives in the drawers, 

see table. 

 

Pos: 93.102 /BA/Ei nstellungen/Schneidwer k/Schnittl änge einstell en/Schnittl äng e T abelle durch Messer bestückung Big Pack HS mit 16 Messer @ 192\mod_1382081539305_78.docx @ 1637876 @  @ 1 

 

Table cutting length depending on blade fitting 

Cutting length mm 

Number of blades 

Used blade compartment 

- 

0 

any one  

44 

16    

each 

88 

8 

each second 

 

176 

4 

each third  

 

Pos: 93.103 /BA/Wartung/Schneidwer k/Schnei dwer k absenken  zÜ  @ 275\mod_1404468973233_78.docx @ 2069532 @  @ 1 

 

Lowering the cutting system 

Pos: 93.104 /BA/Wartung/Schneidwer k/Schnei dwer k absenken: M edi um–El ektroni k @ 356\mod_1438698331389_78.docx @ 2654895 @  @ 1 

 

Medium electronics 

•  Actuate the control unit (

) on the tractor until the cutting unit has been fully lowered. 

Pos: 93.105 /Layout M odul e /----------------Leerzeil e 5 Pt.-------------------- @ 120\mod_1342592918145_0.docx @ 1092566 @  @ 1 

 

 

Pos: 93.106 /BA/Maschi nenbeschrei bung/M aschinenübersicht/Gr oßpackenpr essen/Komfort-Elektroni k @ 61\mod_1299223046976_78.docx @ 570919 @  @ 1 

 

Comfort - Electronic 

Pos: 93.107 /BA/Info-C enter /CCI-ISOBUS-T ermi nal/CCI-Bi G Pack/F unktionstasten F 1 bis F 12Messer bal ken fr eischalten @ 352\mod_1437392672909_78.docx @ 2634130 @  @ 1 

 

Release 

•  To release the blade bar, press 

. 

The symbols 

,

 are shown on the display. 

Pos: 93.108 /BA/Info-C enter /CCI-ISOBUS-T ermi nal/CCI-Bi G Pack/F unktionstasten F 1 bis F 12Messer bal ken senken @ 352\mod_1437393051647_78.docx @ 2634192 @  @ 1 

 

Lowering 

•  To lower the blade bar, press and hold 

.   

Pos: 93.109 /Layout M odul e /----------------Leerzeil e 5 Pt.-------------------- @ 120\mod_1342592918145_0.docx @ 1092566 @  @ 1 

 

 

Pos: 93.110 /BA/Wartung/Schneidwer k/Schnei dwer k absenken: Komfort- Elektroni k Ü ber di e T asten @ 275\mod_1404467742434_78.docx @ 2069479 @  @ 1 

 

Using the pushbuttons on the machine 

•  To lower the blade bar, press the 

 pushbutton until the blade bar is fully lowered. 

Pos: 93.111 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Summary of Contents for 870 HDP

























































































































































































































































































































































































































































































































































































Reviews:

No comments