manualshive.com logo in svg

Krone 870 HDP, Original Operating Instructions, Page: 31 / 568

Share
Download
Krone 870 HDP Original Operating Instructions Download Page 31

 

Safety

 

31 

 

Pos: 21.7 /Überschriften/Überschriften 3/K-O/MMaschi ne sicher ankuppel n @ 274\mod_1404282415732_78.docx @ 2062014 @ 3 @ 1 

 

3.5.3 

Coupling the machine safely 

Pos: 21.8 /BA/Sicher heit/3. Sicherheitsr outinen/Maschi ne an den Tr aktor ankuppel n (Bi G PAC K) @ 273\mod_1404105657612_78.docx @ 2057995 @  @ 1 

 

 

WARNING! 

Risk of injury when coupling the machine 

The machine or machine parts may move unintentionally while the machine is coupled to the 

tractor. As a result, people may be seriously injured or killed. 
•  When coupling the machine, perform the following steps: 

 
•  Never stand between the tractor and the machine while coupling the machine to the tractor. 
•  Depressurise the tractor hydraulics. 
•  Switch off the electronic systems. 
•  Shut down and safeguard the machine, see chapter Safety, "Shutting down and 

safeguarding the machine". 

•  Only couple the hydraulic hoses if the hydraulic systems on the tractor and the machine are 

depressurised. 

•  Couple the compressed air braking system, depending on the version of the machine. 
•  Couple the hydraulic brake, depending on the version of the machine. 
•  Couple and secure the universal shaft. 
•  Connect the lighting cable. 
•  Connect the power cable. 
•  Connect the terminal. 
 

Pos: 21.9 /Überschriften/Überschriften 3/K-O/MMaschi ne sicher abkuppel n @ 274\mod_1404282542952_78.docx @ 2062072 @ 3 @ 1 

 

3.5.4 

Uncoupling the machine safely 

Pos: 21.10 /BA/Sicherheit/3. Sicher hei tsrouti nen/M aschine vom Tr aktor abkuppeln - mit Elektroni k, mi t Br emsen @ 273\mod_1404106986183_78.docx @ 2058054 @  @ 1 

 

 

WARNING! 

Risk of injury when uncoupling the machine 

The machine or machine parts may move unintentionally while the machine is being uncoupled. 

As a result, people may be seriously injured or killed. 
•  When uncoupling the machine, perform the following steps: 

 
•  Shut down and safeguard the machine, see chapter Safety, "Shutting down and 

safeguarding the machine". 

•  Lower the support jack. 
•  Depressurise the tractor hydraulics. 
•  Switch off the electronic systems. 
•  Only uncouple the hydraulic hoses if the hydraulic systems on the tractor and the machine 

are depressurised. 

•  Uncouple the compressed air brake, depending on the version of the machine. 
•  Uncouple the hydraulic brake, depending on the version of the machine. 
•  Disconnect the lighting cable from the tractor. 
•  Disconnect the power cable from the tractor. 
•  Uncouple the universal shaft and place it on the holder provided. 
•  Never stand between the tractor and the machine when uncoupling the machine from the 

tractor. 

 

Pos: 21.11 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Summary of Contents for 870 HDP

























































































































































































































































































































































































































































































































































































Reviews:

No comments