manualshive.com logo in svg

Krone 870 HDP, Original Operating Instructions, Page: 111 / 568

Share
Download
Krone 870 HDP Original Operating Instructions Download Page 111

 

Start-up

 

111 

 

Pos: 79.65.1 /Ü berschriften/Ü berschriften 2/F-J/J/Joystick anschließen @ 366\mod_1441171346670_78.docx @ 2691365 @ 2 @ 1 

 

9.9 

Connecting the Joystick 

Pos: 79.65.2 /BA/Info-Center/CCI-ISOBUS-T er minal/Hinweis: F ür den Anbau des Joysticks Joystick-BA beachten. @ 377\mod_1443162614037_78.docx @ 2736376 @  @ 1 

 

 

Note 

Observe the provided operating instructions of the joystick for the installation of the joystick in 

the tractor cabin. 

 

Pos: 79.65.3 /Ü berschriften/Z wischenüberschriften/K-O/KRON E ISOBU S-Ter minal bei  Traktor en mi t integriertem ISOBU S-System @ 378\mod_1443515088220_78.docx @ 2740129 @  @ 1 

 

KRONE ISOBUS-Terminal for tractors with integrated ISOBUS system 

Pos: 79.65.4 /BA/Sicherheit/8. Voraussetzung en/Handlungsanweisung für all e M aschinen/Voraussetzung: Die Maschi ne ist stillgesetzt und gesicher t, .... @ 259\mod_1398674434170_78.docx @ 1979947 @  @ 1 

 

Prerequisite: 

–  Shut down and safeguard the machine, see chapter Safety, "Shutting down and 

safeguarding the machine". 

Pos: 79.65.5 /Layout Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_1342592918145_0.docx @ 1092566 @  @ 1 

 

 

Pos: 79.65.6 /BA/Info-Center/CCI-ISOBUS-T er minalJoystick an CC I T ermi nal  anschließ en (Traktor mit integriertem ISOBU S System) (2016- 04- 22 10:43:45) @ 366\mod_1441171654174_78.docx @ 2691395 @  @ 1 

 

6

5

1

2

3

4

CC00602

1

4

7

3

6

9

7

5

7

6

 

Fig. 67 
 

 

Note 

The terminal is connected to the tractor via a special cable set (5) which can be ordered by 

stating the KRONE article no. 20 081 223 0. 

 
•  Connect the plug (2) of the cable set (5) with the socket (1) (CAN1-IN) of the terminal. 
•  Connect the plug (4) of the cable set (5) with the socket (3) (CAN1-out) of the terminal. 
•  Connect the ISO plug (6) (9-pole) of the cable set (5) with the ISO socket (6) (9-pole) of the 

joystick. 

•  Connect the ISO plug (7) (9-pole) of the joystick with the ISO socket (7) (9 pole) located in 

the cabin. 

 

Pos: 79.65.7 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Summary of Contents for 870 HDP

























































































































































































































































































































































































































































































































































































Reviews:

No comments