manualshive.com logo in svg

Krone 870 HDP, Original Operating Instructions, Page: 266 / 568

Share
Download
Krone 870 HDP Original Operating Instructions Download Page 266

Settings

 

 

266 

 

Pos: 93.60 /BA/Ei nstellungen/Groß packenpresse/Garnrieg el/Ober nadel wellle spannen / entspannen BiG PACK 870 HD P b=235 mm @ 271\mod_1402655757439_78.docx @ 2043500 @ 2 @ 1 

 

19.10 

Tensioning/relieving the upper needle shaft   

2

3

1

 

Fig. 187  
The upper needle shaft (1) is tensioned or relieved by means of the spring (2). 

 

Prerequisite: 

–  The knotter gear is in the idle position, see chapter Settings "Adjusting the needle yoke 

brake".  

–  The flywheel brake is applied. 
 

Tensioning 

•  To tension the spring (2), tighten the nut (3) until dimension "b" = 235 mm, measured 

between the eyes of the spring. 

 

Relieving 

•  To relieve the spring (2), unwind the nut (3) to the thread end of the eyebolt. 
 

Pos: 93.61 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Summary of Contents for 870 HDP

























































































































































































































































































































































































































































































































































































Reviews:

No comments