manualshive.com logo in svg

Krone 870 HDP, Original Operating Instructions, Page: 129 / 568

Share
Download
Krone 870 HDP Original Operating Instructions Download Page 129

 

Driving and Transport

 

129 

 

Pos: 81.70.7 /Ü berschriften/Ü berschriften 3/P-T/T/T astr äder sichern @ 382\mod_1444211893669_78.docx @ 2754110 @ 3 @ 1 

 

10.5.2 

Securing guide wheels  

Pos: 81.70.8 /BA/F ahr en und Transport/Gr oßpackenpr esse/Transport/T astr äder sicher n_Bild_BP @ 382\mod_1444211627010_78.docx @ 2753988 @  @ 1 

 

BPHS0324

4

3

2

1

 

Fig. 84  

Pos: 81.70.9 /BA/F ahr en und Transport/Gr oßpackenpr esse/Transport/T astr äder sicher n_Text_BP @ 382 \mod_1444211627701_78.docx @ 2754019 @  @ 1 

 

On the right and left sides of the machine: 
•  Raise the pick-up (1). 
•  Feed a cable tie (4) through the borehole (2) and through the frame of the guide wheel (3). 
•  Tighten the cable tie (4). 
 

Pos: 82 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Summary of Contents for 870 HDP

























































































































































































































































































































































































































































































































































































Reviews:

No comments