Krone 870 HDP Original Operating Instructions Download Page 114 | Manualshive

Page: 114 / 568

Krone 870 HDP Original Operating Instructions Download Page 114

Start-up

114

Pos: 79.67 /Ü berschriften/Ü berschriften 2/A-E/BBel euchtung @ 0\mod_1195658399935_78.docx @ 1881 @ 2 @ 1

9.10

Lighting

Pos: 79.68 /BA/Inbetri ebnahme/Groß packenpresse/Beleuchtung/Bel euchtung anschließ en Bil d HD P II @ 171\mod_1370344610812_78.docx @ 1475988 @ @ 1

BPHS0216

1

2

3

Fig. 70

Pos: 79.69 /BA/Sicherheit/8. Voraussetzungen/Handlungsanweisung für all e M aschinen/Handlungsanweisung: M aschine stillsetzen und sichern @ 274\mod_1404365253849_78.docx @ 2065151 @ @ 1

• Shut down and safeguard the machine, see chapter Safety -> Safety routines, "Shutting

down and safeguarding the machine".

Pos: 79.70 /BA/Inbetri ebnahme/Schwader /Anschluss Beleuchtung/Anschluss Beleuchtung Text @ 36\mod_1260783798936_78.docx @ 336718 @ @ 1

The lighting system is connected via the 7-pin connection cable (1).
To do this:
•  Insert the 7-pin plug of the connection cable (1) into the relevant socket (2) of the tractor.
•  Insert the 7-pin connection cable plug (1) into the appropriate socket (3) of the machine.
•  Position the cable so that it will not come in contact with the wheels.

Pos: 79.71 /BA/Inbetri ebnahme/Schwader /Hinweis Sauber keit der Stecker und Steckdosen @ 2\mod_1202399563131_78.docx @ 59273 @ @ 1

Note

Before inserting the plugs, make certain the plugs and sockets are clean and dry. Dirt and

moisture may result in short circuits!

Pos: 79.72.1 /Ü berschriften/Ü berschriften 2/P-T/SSicher ungskette ver wenden @ 6\mod_1214542336632_78.docx @ 94799 @ 2 @ 1

9.11

Using the safety chain

Pos: 79.72.2 /BA/Inbetri ebnahme/Sicherungskette U SA/WARNUN G - F alsch dimensionierte Sicher ungskette ver wendet mit Variante @ 180\mod_1376576652355_78.docx @ 1547873 @ @ 1

WARNING!

When using a wrongly dimensioned safety chain, the safety chain may tear if the

machine loosens unintentionally. This can result in serious accidents.

• Always use a safety chain with a minimum tensile strength of 178 kN (40.000 lbf).

Pos: 79.72.3 /BA/Inbetri ebnahme/Sicherungskette U SA/Hinweis Sicherungskette Länder abhängig @ 6\mod_1214999654856_78.docx @ 97933 @ @ 1

Note

Using the safety chain
Attachment of the safety chain is not stipulated in all countries.

Pos: 79.72.4 /BA/Inbetri ebnahme/Sicherungskette U SA/Sicher ungskette ver wenden @ 207 \mod_1386742973026_78.docx @ 1714836 @ @ 1

The safety chain is used as an additional safety precaution for trailed devices, should they

become detached from the drawbar during transport. Attach the safety chain with the respective

mounting parts to the hitching device on the tractor or to another specified connection point. The

safety chain should have just enough play to be able to go around curves.

Pos: 79.72.5 /BA/Bei packs/Sonstige/Sicherungskette 178 kN /Sicher ungskette monti eren BiG Pack Bild @ 147\mod_1361184126131_78.docx @ 1320037 @ @ 1

«
...
112
113
114
115
116
...
»

Summary of Contents for 870 HDP

























































































































































































































































































































































































































































































































































































Reviews:

No comments