manualshive.com logo in svg

Krone 870 HDP, Original Operating Instructions, Page: 422 / 568

Share
Download
Krone 870 HDP Original Operating Instructions Download Page 422

4

Basic safety instructions

4.13

Road safety

16

Supplement to Operating Instructions 150000774_00 _en

BiG Pack 870 HDP, BiG Pack 870 HDP XC

Description, declaration and order numbers of safety labels, .

4.13

Road safety

Dangers in road traffic

If the machine exceeds maximum dimension and weights specified by national law and if it is
not properly lit, other road users could be endangered when driving on public highways.

„

Before road travel, ensure that the maximum permissible dimensions, weights and axle
loads, supported loads and hitching loads which apply according to national law for driving
on public roads are not exceeded.

„

Before road travel, switch on lighting and ensure the proper function.

Danger when driving on road and field

Hitched and mounted machines change the handling characteristics of the tractor. The handling
characteristics depend for instance on operating state and ground. If changed handling
characteristics are not considered, the driver may cause accidents.

„

Observe measures for driving on road and field,.

Danger due to machine which is not prepared properly for road travel

If the machine is not prepared properly for road travel, serious accidents may occur on the
roads.

„

Before driving on roads, prepare the machine for road travel,.

Danger of tipping over on slopes

The machine may tip over when driving on slopes. Thus there is a risk of accidents, serious
injuries or death. The risk of tipping over depends on many factors.

„

Observe measures for driving,.

Dangers when cornering with trailed trailer

When cornering, the trailer swivels out more than the self-propelled machine. This may result in
accidents.

„

Consider the larger swivel range.

„

Consider people, oncoming traffic and obstacles when turning.

4.14

Parking the machine safely

An improperly parked machine may move uncontrollably or overturn. People may be injured or
killed.

„

Put machine down on firm and level ground.

„

Before adjusting, repairing, servicing and cleaning the machine, ensure that it is securely
positioned.

„

Note section “Parking the machine” in chapter Driving and Transport, .

Summary of Contents for 870 HDP

























































































































































































































































































































































































































































































































































































Reviews:

No comments