manualshive.com logo in svg

Krone 870 HDP, Original Operating Instructions, Page: 254 / 568

Share
Download
Krone 870 HDP Original Operating Instructions Download Page 254

Settings

 

 

254 

 

Pos: 93.25 /Ü berschriften/Ü berschriften 2/P-T/RR ollenni ederhalter @ 0\mod_1201163046930_78.docx @ 51122 @ 2 @ 1 

 

19.3 

Roller crop guide  

Pos: 93.26 /BA/Sicherheit/Pick-up / R ollenni ederhalter/War nung! - Abbau des Roll enniederhalters @ 274\mod_1404216918043_78.docx @ 2060895 @  @ 1 

 

 

WARNING!  

Risk of injury if the machine is used without a roller crop guide! 

If the machine is operated without a roller crop guide, people can be seriously injured or killed. 
•  The roller crop guide is used for accident protection and must not be removed during 

operation. 

 

Pos: 93.27 /BA/Ei nstellungen/Pick-up / R ollenni ederhalter/R ollenni ederhalter Bil d BiG Pack 4x4 H S @ 71\mod_1305807701420_78.docx @ 641126 @  @ 1 

 

 

Fig. 173 

Pos: 93.28 /BA/Sicherheit/8. Voraussetzungen/Handlungsanweisung für all e M aschinen/Handlungsanweisung: M aschine stillsetze n und sichern @ 274\mod_1404365253849_78.docx @ 2065151 @  @ 1 

 

•  Shut down and safeguard the machine, see chapter Safety -> Safety routines, "Shutting 

down and safeguarding the machine". 

Pos: 93.29 /BA/Ei nstellungen/Pick-up / R ollenni ederhalter/R ollenni ederhalter H öhenei nstellung @ 20\mod_1238588056307_78.docx @ 223090 @  @ 1 

 

The roller crop guide (1) provides for the regulation during conveyance of the crop. It provides 

for a continuous crop collection by the Pick-up. 
Adjust the height of the roller crop guides (1) so that the roller of the holding-down device (2) 

continuously runs above the swath. 
The height adjustment of the roller crop guide (1) can be made on the retaining chains (3) that 

are suspended on the support (4) on either side of the machine. 
 

 

Note 

Make certain that the chains in the supports are of the same length. 

 

Pos: 93.30 /BA/Ei nstellungen/Pick-up / R ollenni ederhalter/Aufl agedruck der Ni ederhalteroll e BP 12130 HS @ 71\mod_1305807916536_78.docx @ 641184 @  @ 1 

 

The spring (5) sets the ground pressure of the holding-down roller (2) to the swath. 
•  By tightening or loosening the nut (6) on the eye screw (7), set the required ground 

pressure 

 

Dry forage: Increase ground pressure 

Moist forage: Reduce ground pressure 

 

Pos: 93.31 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Summary of Contents for 870 HDP

























































































































































































































































































































































































































































































































































































Reviews:

No comments