manualshive.com logo in svg

Krone 870 HDP, Original Operating Instructions, Page: 103 / 568

Share
Download
Krone 870 HDP Original Operating Instructions Download Page 103

 

Start-up

 

103 

 

Pos: 79.43.1 /Ü berschriften/Ü berschriften 2/F-J/IISO-Stecker ableg en @ 364\mod_1440594785663_78.docx @ 2681127 @ 2 @ 1 

 

9.3 

Putting Down ISO Plug 

Pos: 79.43.2 /Beipacks/Sonstige Beipacks_maschi nenuebergreifend/ISOBUS- Kabel/Beipack IOSBUS-Kabel _ISO- Stecker  ableg en BiG Pack Bil d @ 364\mod_1440513852606_78.docx @ 2679724 @  @ 1 

 

ZB

BP

22

94

3

9
8

10

 

Fig. 60  

Pos: 79.43.3 /Beipacks/Sonstige Beipacks_maschi nenuebergreifend/ISOBUS- KabelBeipack ISOBU S-Kabel _ISO-Stecker ablegen BiG Pack T ext @ 364\mod_1440594954540_78.docx @ 2681157 @  @ 1 

 

• 

For version with hydraulic brake (export):

 Dismount hydraulic hose (10) of hydraulic 

brake from hose support and mount it on the opposite side. 

•  Remove chain from ISO plug (3) and from protective cap (9). 
•  Insert protective cap (9) of ISO plug (3) from above into the opening of the hose support 

and secure by using the nut (8). 

•  Mount ISO plug (3).  

Pos: 79.44 /Ü berschriften/Ü berschriften 2/F-J/HH ydr aulische Bremse (Export) @ 17\mod_1236332990291_78.docx @ 204927 @ 2 @ 1 

 

9.4 

Hydraulic brake (Export)  

Pos: 79.45 /BA/Inbetri ebnahme/H ydraulische Br emse/H ydr aulische Bremse Export Bild Bi G Pack 870 @ 271\mod_1402645961427_78.docx @ 2042698 @  @ 1 

 

 

Fig. 61 

Pos: 79.46 /BA/Sicherheit/8. Voraussetzungen/Handlungsanweisung für all e M aschinen/Handlungsanweisung: M aschine stillsetze n und sichern @ 274\mod_1404365253849_78.docx @ 2065151 @  @ 1 

 

•  Shut down and safeguard the machine, see chapter Safety -> Safety routines, "Shutting 

down and safeguarding the machine". 

Pos: 79.47 /BA/Inbetri ebnahme/H ydraulische Br emse/H ydr aulische Brems e ( Export) @ 17\mod_1236333662166_78.docx @ 204952 @  @ 1 

 

A hydraulic brake is provided for certain export versions. In this version, the corresponding 

hydraulic hose is connected with the control valve on the tractor side. The brake is activated by 

actuating the tractor brake pedal. 

Pos: 79.48 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Summary of Contents for 870 HDP

























































































































































































































































































































































































































































































































































































Reviews:

No comments