![background image](http://html1.mh-extra.com/html/icom/d-star-id-4100a/d-star-id-4100a_advanced-manual_611923072.webp)
4
D-STAR OPERATION
4-35
Step 7. Changing the repeater group
L
The repeater group that is selected in ‘Step 1.
Selecting the repeater group’ is displayed. You can
skip this setting and go to the next item. To change
the group, follow the steps, described below.
1. Select “GROUP,” then push [
ï
].
•Enters the repeater group selection mode.
2. Select the repeater group, 01 to 50, then push
[
ï
].
Step 8. Setting “USE(FROM)” to be used as an
Access repeater
L
You can use the entered repeaters as an access
repeater when using the DR function. When not
using as an access repeater, select “NO,” and go to
‘15. Selecting the position data accuracy level.’ In
that case, the entered repeater is not displayed in
the “FROM” field.
1. Select “USE(FROM),” then push [
ï
].
2. Select “YES” to use the repeater as an access
repeater, then push [
ï
].
Step 9. Entering the access repeater frequency
1. Select “FREQUENCY,” then push [
ï
].
•Enters the frequency entry mode.
2. Rotate [DIAL] to enter the repeater frequency,
then push [
ï
].
L
Push [MW] to move the cursor forwards, or push
[MODE] to move the cursor backwards to select a
digit to enter.
Step 10. Selecting the duplex direction
L
When ‘Step 2. Selecting the communication type’
is set to “DV Simplex” or “FM Simplex,” this item is
not displayed.
L
“DUP–” is automatically set when the access
repeater frequency is entered in ‘Step 9. Entering
the access repeater frequency.’
L
If necessary, you can change the duplex direction.
1. Select “DUP,” then push [
ï
].
2. Select a duplex direction, then push [
ï
].
•OFF: Turn the duplex function OFF.
•DUP–: The transmit frequency shifts down from the
receive frequency by the offset amount.
•DUP+: The transmit frequency shifts up from the
receive frequency by the offset amount.
Step 11. Entering the frequency offset
L
When ‘Step 2. Selecting the communication type’
is set to “DV Simplex” or “FM Simplex,” this item is
not displayed.
L
The offset value* is automatically set when the
access repeater frequency is entered in ‘Step 9.
Entering the access repeater frequency.’
* The default value differs, depending on the transceiver
version.
L
If necessary, you can change the frequency offset.
1. Select “OFFSET FREQ,” then push [
ï
].
•Enters the frequency offset entry mode.
2. Rotate [DIAL] to enter the frequency offset
between 0.000.00 ~ 59.995.00 MHz, then push
[
ï
].
L
Push [MW] to move the cursor forwards, or push
[MODE] to move the cursor backwards to select a
digit to enter.
Step 12. Setting the FM mode
L
When ‘Step 2. Selecting the communication type’ is
set to “DV Repeater” or “DV Simplex,” this item is
not displayed.
1. Select “MODE,” then push [
ï
].
•Enters the operating mode setting mode.
2. Select “FM” or “FM-N,” then push [
ï
].
Step 13. Setting the tone
L
When ‘Step 2. Selecting the communication type’ is
set to “DV Repeater” or “DV Simplex,” this item is
not displayed.
1. Select “TONE,” then push [
ï
].
•Enters the tone setting mode.
2. Select the option, then push [
ï
].
•OFF: Turn the tone function OFF.
•TONE: Select when the repeater requires an access
tone.
•TSQL: Select when you want to use the tone squelch
operation in simplex.
Step 14. Selecting the repeater tone frequency
L
When ‘Step 2. Selecting the communication type’ is
set to “DV Repeater” or “DV Simplex,” this item is
not displayed.
L
This setting is required when ‘Step 13. Setting the
tone’ is set to “TONE” or “TSQL.”
1. Select “REPEATER TONE,” then push [
ï
].
•Enters the repeater tone setting mode.
2. Rotate [DIAL] to select the repeater tone
frequency, then push [
ï
].
Entering new information into the Repeater List
D
Entering new information into the repeater list (Continued)
Previous view