Control Codes
YOFF (2 bytes):
Y direction offset
FLAG (1 byte):
Specifies the HRI printing
Data:
Bar code data
For bar code printing precautions, see “Notes on bar code printing” on
page B-3.
63.Set Fixed Length Image: FS (X
'
1C
'
)
This code is used to substitute for ESC %1 or n1 n2 or ESC %2 n1 n2.
To print image data, it is recommended that ESC %1 n1 n2 or ESC %2
n1 n2 be used.
Before this control code is used, valid n1 and n2 must be specified in
the ESC %1 or ESC %2 sequence. The values of n1 and n2 referred to
at this time are those specified most recently. The number of data bytes
following this control code should not contradict with the values of the
previously specified n1 and n2.
64.Set 3 Byte Transfer Mode: ESC ( (X
'
1B 28
'
)
Same as ESX 0E 00 01 15 (X
'
1B 7E 0E 00 01 15
'
). It is recom-
mended that ESX 0E 00 01 15 be used whenever possible.
65.Set 2 Byte Transfer Mode: ESC ) (X
'
1B 29
'
)
Same as ESX 0E 00 01 16 (X
'
1B 7E 0E 00 01 16
'
). It is recom-
mended that ESX 0E 00 01 16 be used whenever possible.
66.Set Page Length: ESC F n1 n2 (X
'
1B 46 n1n2
'
)
Same as ESX 04 00 03 00 n1 n2 (X
'
1B 7E 04 00 03 00 n1 n2
'
). It is
recommended that ESX 04 00 03 00 n1 n2 be used whenever possible.
67.Set High Speed Mode: ESC O (X
'
1B 4F
'
)
Same as ESX 0E 00 01 01 (X
'
1B 7E 0E 00 01 01
'
). It is recom-
mended that ESX 0E 00 01 01 be used whenever possible.
68.Cancel High Speed Mode: ESC P (X
'
1B 50
'
)
Same as ESX 0E 00 01 02 (X
'
1B 7E 0E 00 01 02
'
). It is recom-
mended that ESX 0E 00 01 02 be used whenever possible.
69.Eject Cut Sheet: ESC V (X
'
1B 56
'
)
Same as ESX 0E 00 01 06 (X
'
1B 7E 0E 00 01 06
'
). It is recom-
mended that ESX 0E 00 01 06 be used whenever possible.
70.Set Character Enlargement: ESC [ (X
'
1B 5B
'
)
Same as ESX 0E 00 01 09 (X
'
1B 7E 0E 00 01 09
'
). It is recom-
mended that ESX 0E 00 01 09 be used whenever possible.
71.Cancel Character Enlargement: ESC ] (X
'
1B 5D
'
)
Same as ESX 0E 00 01 0A (X
'
1B 7E 0E 00 01 0A
'
).
It is recommended that ESX 0E 00 01 0A be used whenever possible.
Appendix C. Control Codes (Connected to a Parallel Port)
C-21
Summary of Contents for 5400-006
