manualshive.com logo in svg

Honeywell Thor VM3, User Manual, Page: 119 / 378

Share
Download
Honeywell Thor VM3 User Manual Download Page 119

Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide

107

External AC/DC Power Supply

The optional external AC/DC power supply is for use in environments, such as an office, 
where DC power is not available.

Note:

The Honeywell-approved AC/DC Power Supply and Adapter Cable are only intended for 
use in a 40ºC (104ºF) maximum ambient temperature environment.

In North America, this unit is intended for use with a UL Listed ITE power supply with 
output rated 15 VDC, 4 Amp (maximum), 60 W (maximum). Outside North America, this 
unit is intended for use with an IEC certified ITE power supply with output rated 15 VDC, 
4 Amp (maximum), 60 W (maximum).

The external power supply may be connected to either a 120V, 60Hz supply or, outside 
North America, to a 230V, 50Hz supply, using the appropriate detachable cordset. In all 
cases, connect to a properly grounded source of supply provided with maximum 15 
Amp overcurrent protection (10 Amp for 230V circuits).

Connect External Power Supply

1. Connect the provided detachable cordset (US only, all others must order cable sepa-

rately) to the external power supply (IEC 320 connector).

2. Plug cordset into appropriate, grounded, electrical supply receptacle (AC mains).

3. Connect the DC output cable end to the corresponding connector on the adapter 

cable.

4. Connect the watertight connector end of the Adapter Cable to the VMXD Off-Vehicle 

Dock power connector by aligning the connector pins to the power connector; push 
down on the watertight connector and twist it to fasten securely.

5. Press the 

Power Switch

 on the back of the Thor VM3 dock.

6. Press the 

Power Button

 on the front of the Thor VM3 to turn on the Thor VM3.

These instructions for use with 

VMXD Enhanced Dock for Off-Vehicle Use

 

only.

AC Input Cable (US only)

DC Output Cable

To DC Output Cable

To Dock

Summary of Contents for Thor VM3



























































































































































































































































































































































































Reviews:

No comments