manualshive.com logo in svg

Honeywell Thor VM3, User Manual, Page: 211 / 378

Share
Download
Honeywell Thor VM3 User Manual Download Page 211

Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide

199

Result

The Thor VM3 continues to run and follows the Ignition Control/Ignition On power 
scheme with timers reset at the time Ignition switched to Active.

An example of this case would be a Thor VM3 that is running on UPS and is then 
mounted on a dock that has truck power and the ignition switch is already On.

Thor VM3 is On and Vehicle Ignition is Switched to Off

Conditions

The Thor VM3 is On and vehicle ignition changes from On to Off.

Result

 The Thor VM3 follows the Ignition Control/Ignition Off power scheme with timers reset 
at the time Ignition switched to Inactive. UPS charging is disabled.

An example of this case would be a Thor VM3 that is running on UPS and is then 
mounted on a dock that has truck power and the ignition switch is already Off.

Auto-On Mode

In Auto-On mode, the Thor VM3 is turned On by the presence of external power with no 
user interaction required. Ignition input is ignored when Auto-On Mode is enabled.

Note:

When the UPS battery has been depleted or disconnected (the Thor VM3 is first powered 
out of the box, the front panel has been replaced, etc.) power the Thor VM3 manually by 
pressing the power button. After the initial power up, the Thor VM3 powers on 
automatically when power is attached and Auto-On mode is selected.

Note:

When Auto-On is used to power the Thor VM3 on automatically the 

Wakeup Timer

 must be 

enabled.

Thor VM3 is Off

Conditions

The Thor VM3 is Off and gets external power, such as

•

Thor VM3 is installed on a powered dock with the dock power switch On

•

Thor VM3 is already mounted to a dock and external power is applied to the dock

•

Thor VM3 is already mounted to a dock and the dock power switch is turned On

Result

The Thor VM3 boots. Once booted the Thor VM3 follows the Auto-On power scheme 
with timers reset after the boot completes.

Thor VM3 is On

Conditions

The Thor VM3 is On and gets external power, such as

•

Thor VM3 is installed on a powered dock with the dock power switch On

Summary of Contents for Thor VM3



























































































































































































































































































































































































Reviews:

No comments