![background image](http://html1.mh-extra.com/html/gmc/1989-light-duty-truck/1989-light-duty-truck_repair-manual_2235153922.webp)
7 B 3 -10 NEW PROCESS TRANSMISSION
*
A ssem ble (Figure 15)
1. Install the detent cams (488), a new retainer clip and
the spring.
2. Shift shafts (480 and 481).
• Coat the cover bores with grease.
• Install the shafts in the positions they were
removed from.
3. Install new seals and the retainers (483).
4. Install the shift levers (484 and 487).
• The 3rd and overdrive lever must point down.
486
484. 1st and 2nd Shift
Lever
485. Washer
450. Side Cover
486. Nut
480. 3rd and Overdrive
487. 3rd and 4th
Shift Shaft
S hift Lever
481.
1
st and
2
nd
488. Detent Cam
Shift Shaft
489. Retaining Clip
482. Shift Shaft Seal
490. Detent Spring
483. Retainer
B-08315
Figure 15— Side Cover and Components
TRANSMISSION ASSEMBLY
(INSTALLATION OF SUB-ASSEMBLIES)
Use new seals, gaskets and thread sealer on all bolt
threads when assembling the transmission. Tighten all
bolts to specified torque.
Lubricate all assemblies as they are installed in the
transmission case using transmission oil.
Install or C onnect (Figure
2)
Tool Required:
J 29793 Countershaft Alignment Tool
1. Countergear (430) and the thrust washers.
• Lower the countergear into place with the front
thrust washer tabs inthe case slots.
• Align the rear thrust washer tabs with the case
slots and slide it in.
2. Mainshaft (418) and a new snap ring (454) into the
extension housing (416).
3. Extension housing (416) and a new gasket onto the
case.
• Turn the extension housing upside down and
install one screw to hold it in place (figure 3).
4. Main drive gear (405).
• Tap the gear in until the bearing snap ring bot
toms against the case.
Im p o rtan t
• The main drive gear must fit smoothly into
place, if it does not, check to see that all com
ponents of the mainshaft are in the proper po
sitions.
5.
Countershaft (429) and the woodruff key.
• Lift the countergear into mesh with the main
shaft. Be sure the thrust washers are in place.
• Push the countershaft half way into the coun
tergear and install the woodruff key.
• Push the countershaft into place and remove
J 29793.
6
. Reverse shift shaft (443) and a new seal.
7. Reverse idler shaft (424) and the reverse gear.
• Push the shaft in part way.
• Put the gear onto the shaft with the fork slot to
the rear and engage the slot with the reverse
shift shaft fork (figure 16).
• Install the woodruff key and drive the shaft
flush with the case.
8
. Extension housing screws.
• Do not damage the gasket when turning the
housing into place.
9. Bearing retainer (401) and a new gasket.
10. New countershaft plug (432).
Summary of Contents for 1989 Light Duty Truck
