background image

MODEL 700 THROTTLE BODY  6C4-5

IDLE AIR CONTROL (IAC) VALVE

N O TIC E:  The  IA C   valve  is  an  e le c tric a l  c o m p o ­

n e n t a n d  m u s t n o t b e  so a k e d  in an y liq u id  c le a n e r

 

o r   solvent.  O th e rw is e  d a m a g e  c o u ld  result.

Important

On  TBI  Model  700,  the  IAC valve  is flange-mounted, 
with dual taper,  10mm diam eter pintle.  If replacem ent 
is  necessary,  only  an  IAC  valve  identified  with  the 

correct  part  num ber  (having  the  appropriate  pintle 
shape and diameter) should be used.

Remove or Disconnect (Figure 9)

1.  Screw assemblies and  IAC valve.

2.  IAC valve o-ring and discard.

3.  T hrottle Position S ensor

4.  TPS A ttaching S crew  & W asher A ssem bly

F-6755

TUBE MODULE ASSEMBLY

Remove or Disconnect (Figure 10)

1.  Tube module assem bly attaching screws.

2.  Tube module assembly.
3.  Tube module assem bly gasket and discard.

Figure 8— Throttle Position Sensor (TPS) TBI 700

3

 

2

1.  IA C V Attaching S crew  A ssem bly

2.  External IA C V O -R ing

3.  G rim e Shield

F-6739

Figure 9— Flange Mounted IAC Valve — TBI 700

CLEANING

jtrp

Clean

Metal  throttle  body  parts  in  cold  im m ersion  type 

cleaner, Carbon X (X-55) or equivalent.

N O T IC E :  Do  n o t  im m e rs e   IA C   Valve,  T h ro ttle

 

Position   Sensor,  Fuel In je c to r o r Pressure  R e g u ­
la to r  in  c le a n e r  as  th e y   m ay  b e c o m e   n o n -fu n c -

 

tional.

Old  gasket  material  from  surface  of  throttle  body 
assem bly to  insure proper seal of new gaskets.

IAC valve seating surfaces on throttle body to assure 

proper  seal  of  new  O-ring  and  contact  of  IAC  valve 

flange.

Blow  out  all  passages  in  the  castings  with  co m ­
pressed  air.  Do  not  pass  drill  bits  or  wire  through
 

passages.

Summary of Contents for 1989 Light Duty Truck







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews: