![background image](http://html1.mh-extra.com/html/gmc/1989-light-duty-truck/1989-light-duty-truck_repair-manual_2235153510.webp)
6A5-20 V8 ENGINE
— R ocker arm areas w hich contact the valve stem s
and the sockets w hich co n ta c t the p ushrods.
T h e se a re as s h o u ld be sm oo th and free of
dam age and wear.
— R ocker arm nuts.
• The nuts are prevailing torque nuts. At least
6.2 N-m (55 in. lbs.) torque should be required
to thread the nuts onto the rocker arm studs. If
not, it is possible that the nut(s) could back off
during engine operation, causing loss of lash
and valve train noise.
— Pushrods for bending. Roll the pushrod on a flat
su rfa ce to d ete rm in e if it is bent. R eplace if
necessary.
— Ends of the pushrods for scoring or roughness.
HYDRAULIC LIFTERS
Refer to GENERAL ENGINE MECHANICAL (SEC. 6A).
CYLINDER HEAD
D isassem ble (Figures 37, 38 and 39)
Tool R equired:
J 8062 Valve Spring Compressor
1. Valve keepers (251).
• Compress the springs (256) with J 8062 (figure
39).
• Remove the valve keepers.
• Remove J 8062.
2. Caps (253), shields (255), springs with dampers
(256) and rotators (254).
3. O-ring seals (252) (if used) and seals (257).
4. Valves (258 and 259). Place them in a rack so they
can be re tu rn e d to th e ir o rig in a l p o s itio n at
assembly.
CLEANING AND INSPECTION OF COMPONENTS
Refer to GENERAL ENGINE MECHANICAL (SEC. 6A)
and perform the following:
€
Clean
C om ponents as outlined.
Inspect
C om po n en ts as outlined.
M easure
• Valve stem clearance.
• Valve sp ring tension and free length.
Other information outlined includes:
• Valve and seat grinding.
• Valve guide reaming.
ROCKER ARM STUD REPLACEMENT
(5.0 L AND 5.7 L ENGINES)
Tools Required:
J 5802-01 Stud Remover
J 5715 Reamer (0.003-inch oversize) or
J 6036 Reamer (0.013-inch oversize)
J 6880 Stud Installer
Rocker arm studs that have damaged threads or are
loose in cylinder heads should be replaced. New studs
are available in 0.003-inch and 0.013-inch oversize.
1. Place J 5802-01 over the stud to be removed. Install
a nut and flat washer. Remove the stud by turning
the nut (figure 40).
2. R eam th e h o le to th e p ro p e r s iz e fo r th e
re p la c e m e n t o v e rs iz e s tu d . U se J 5715 fo r
0.003-inch oversize studs; J 6036 for 0.013-inch
oversize studs (figure 41).
3. Coat lower end (press-fit area) of stud with hypoid
axle lubricant. Drive the stud into place with a
hammer and J 6880. Stud is installed to proper
depth when the tool bottoms on the cylinder head
(figure 42).
Summary of Contents for 1989 Light Duty Truck
