DISTRIBUTORS 6D5-9
11
.
12
.
13.
14.
|“H - | Install or Connect
— Pickup coil connector to the module.
— ESC connector (if equipped) to the pickup coil
connector.
— W iring harness and capacitor to the other end of
the module.
Module, wiring harness, and capacitor to the housing
with three bolts.
Shaft assem bly into the housing.
• Rotate the shaft to check for even clearance all
around between the pickup coil assem bly and
the teeth on the distributor shaft assembly. If
interference exists, loosen the three bolts on
the pickup coil assem bly and move the pole
piece (teeth) to provide an even clearance and
tighten the three bolts.
Hall Effect switch (if equipped) to the housing with two
bolts.
Rotor to the shaft assem bly with two screws.
Distributors for 6 Cylinder Engines
15. Driven gear (29) onto the shaft.
Distributors for 8 Cylinder Engines
16. Seal (22), thrust washer, washer (31), and driven gear
(29) onto the shaft.
All Distributors
• Align the tim ing mark (48) on the driven gear with the
rotor tip (47) (figure 20).
17. Roll pin into the driven gear (figure 21).
18. Distributor cap (23) onto the housing (30) with the tab
on the rim of the cap in the notch of the housing.
19. Four spring clips on the cap onto the rim of the hous
ing.
20. Wiring harness connector to the term inal on the side
of the distributor cap (figure 22).
DISASSEMBLY OF
DISTRIBUTORS
WITH SEPARATE COILS
DISTRIBUTORS WITH SEALED MODULE
CONNECTORS (Figure 3)
Remove or Disconnect (Figure 23 and 24)
3.
4.
6
.
8
.
9.
10
.
11
.
12
.
Screws and w ashers holding the cap to the housing.
Cap (23) from the housing.
Place marks on the rotor and the shaft assem bly to
help line up the rotor during assembly.
Rotor (10) from the shaft by lifting or prying straight
up.
Roll pin (27) from the shaft (26).
• Mark the shaft and driven gear for reassembly.
• Drive out the roll pin with a small punch (figure
25).
D riven g ea r (29), w a s h e r or s p rin g , and sp rin g
retainer (52) or tang w asher (33).
Shaft (26) with the pole piece and plate from the hous
ing (30).
Retainer (49) from the housing (30) by prying it with a
screwdriver.
Shield (50).
Pickup coil connector from the m odule (14).
• Lift the locking tab with a screwdriver.
Pickup coil (11).
Two screws holding the m odule to the housing.
Module (14).
5. Ig n itio n C o il C o n n e c to r T e rm in a ls
F-04259
Figure 21—Installing the Roll Pin
Figure 22—Wiring Harness Connector
Summary of Contents for 1989 Light Duty Truck
