![background image](http://html1.mh-extra.com/html/gmc/1989-light-duty-truck/1989-light-duty-truck_repair-manual_2235153481.webp)
4.8 LITER L6 6A4-27
c
B-05254
A. Bearing
B. W asher
C. Stud
D. N ut
Figure 53— Installing the Torsional Damper
|+"»| R em ove or D isco n n ect (Figure 5)
• J-35468 from the seal (158).
Figure 54— Piston Ring Gap Location
PISTON AND CONNECTING
ROD INSTALLATION
TORSIONAL DAMPER
INSTALLATION
|+ *-| Install or C o nn ect (Fig ures 5 and 53)
Tool Required:
J-23523-E Torsional Damper Rem over/Installer
N O T IC E : The in e r tia w e ig h t s e c tio n o f th e
torsional d a m p e r is a s s e m b le d to the h ub w ith a
ru b b e r type m aterial. The c o rre c t installation
p ro c e d u re s (w ith th e p ro p e r to o l) m u s t b e
fo llo w e d o r m o v e m e n t o f th e in e rtia w e ig h t
s ectio n o f the hub w ill d estro y the tuning o f the
d am p er.
1. Key (163).
2. Stud (item C, figure 53) to the crankshaft (154).
Thread the stud fully into the tapped end of the
crankshaft.
3. Torsional dam per (162) over the end of the stud.
Align the keyway in the vibration dam per shaft with
the crankshaft key.
4. Bearing, washer, and nut (figure 53).
• Turn the nut to pull the vibration dam per into
place.
• Remove the tool.
5. Bolt (160) and washer (161).
CONNECTING ROD BEARING SELECTION
Connecting rod bearings are of the precision insert type
and do not use shim s for adjustment. DO NOT FILE
RODS OR ROD CAPS. If clearances are found to be
excessive, a new bearing w ill be required. Service
bearings are available in standard size and 0.001-inch and
0.002-inch undersize for use with new and used standard
size cran ksha fts, and in 0.010-inch and 0.020-inch
undersize for use with reconditioned crankshafts.
T h e s im p le s t, m o s t a c c u ra te w a y to m e a s u re
connecting rod bearing clearance is with the use of
gaging plastic. This wax-like material compresses evenly
betw een th e b e a rin g and jo u rn a l s u rfa ce s w ith o u t
dam aging them.
Selective fitting of the bearing inserts is necessary to
obtain close tolerances. For this reason you may use, for
exam ple, one s ta n d a rd in s e rt w ith one 0.001-inch
undersize insert, w hich w ill decrease the clearance
0.0005-inch from using two standard inserts.
Q
T ig h ten
• Bolt (160) to 80 N m (60 ft. lbs.).
Install or C o nn ect (Fig ures 5 and 54 throu g h
— 56)
Tools Required:
J-5329 Connecting Rod Guide Set
J-8037 Ring Compressor
• Make sure the cylinder walls are clean. Lubricate
the cylinder wall lightly with engine oil.
• Make sure the piston is installed in the m atching
cylinder. Refer to “ Piston and Connecting Rod
Assem blies,” previously in this section.
1. Connecting rod bearing inserts (112 and 113).
• Be certain that the inserts are of the proper
size.
• Install the inserts in the connecting rod (108)
and connecting rod cap (110).
2. Piston (107) and connecting rod (108) to the proper
bore.
Summary of Contents for 1989 Light Duty Truck
