![background image](http://html1.mh-extra.com/html/gmc/1989-light-duty-truck/1989-light-duty-truck_repair-manual_2235153469.webp)
4.8 LITER L6 6A4-15
Figure 24— Checking the Block Gasket Surface
provide the same dim ension as at the other
bores. This is necessary to assure the proper
“ crush” on bearing inserts when the engine is
assembled.
CYLINDER BORES
Inspect
• Cylinder walls for scoring or other damage.
M easure
Cylinder out of round and taper. Refer to GENERAL
ENGINE MECHANICAL (SEC.
6
A).
CYLINDER BORE RECONDITIONING
Refer to GENERAL ENGINE MECHANICAL (SEC.
6
A).
PISTON AND CONNECTING ROD
ASSEMBLIES
Refer to GENERAL ENGINE MECHANICAL (SEC.
6
A)
and perform the following:
❖
j n j l
l V
D isassem ble
Com ponents as required.
C lean
Com ponents as outlined.
Inspect
Com ponents as outlined.
M easure
• Piston pin diameter and pin to piston clearance.
• Piston to bore clearance, and fit pistons as outlined.
*
l v
A ssem ble
Com ponents as outlined.
M easure
Ring end gap and ring clearance.
Inspect
Ring fit.
INTAKE AND EXHAUST
MANIFOLDS
❖
D isassem ble (Fig ure 4)
1. Bolts (39) and washers (40).
2. Nuts (32).
3. Intake manifold (31) and exhaust manifold (37).
4. Gasket (36).
i j i
Figure 2 5 — Main B earing Cap Shim Location
Clean
Old pieces of gasket from the gasket surfaces.
Inspect
Manifolds for cracks, broken flanges, etc.
Gasket surfaces for heavy scratches.
M anifold heat control valve (if used). The heat
c o n tro l valve is in the exha ust m an ifold . The
therm ostatic spring and anti-rattle spring must be in
place and in good condition. The shaft should turn
freely when weight is moved and the spring should
return the shaft to its original position.
M easure
Manifold distortion. Lay a straight edge along the
full length of the exhaust port faces and measure
any gaps between the straight edge and the port
faces. If at any point a gap of 0.80 mm (0.030-inch)
or more exists, it is likely that the manifold has
distorted to a point where it will not seal properly. If a
good exhaust seal is to be expected, the exhaust
manifold must be replaced.
Summary of Contents for 1989 Light Duty Truck
