![background image](http://html1.mh-extra.com/html/gmc/1989-light-duty-truck/1989-light-duty-truck_repair-manual_2235153368.webp)
6
A
1 - 1 2
2.5 LITER L4 ENGINE
A Ridge Reamer
B Cloth
B-05065
Figure 16— Removing the Cylinder Ridge
• Using the m anufacturer’s directions, install a
ridge reamer into the top of the cylinder.
Perform the cutting operation.
• After the ridge and/or deposits are removed,
remove the ridge reamer. Turn the crankshaft
until the piston is at the top of its stroke.
Remove the cloth and the cuttings.
• Repeat this procedure for each piston.
2. Connecting rod caps (116) as follows: Take note of
th e a rra n g e m e n t of th e c o n n e c tin g rod (53)
markings, to insure proper reassembly. Use a silver
pencil to mark the parts if necessary.
• To avoid mismatching the connecting rods and
c o n n e c tin g rod c a p s , re m o ve o n ly one
connecting rod cap at a time. Place the piston
at the bottom of its stroke.
• Remove the nuts (56).
• Remove the connecting rod cap.
• Install two sections of 10 mm (3/s-inch) rubber
hose over the connecting rod studs. This will
p re v e n t th e c o n n e c tin g rod s tu d s fro m
scratching the bore or crankshaft journal
during the removal process.
3. Connecting rod (53) and piston (51) from the block.
• Push the connecting rod and piston from the
block being careful not to let the connecting
rod contact the cylinder bore.
• Loosely assemble the connecting rod cap
(116) onto the connecting rod.
• Take note of, or mark the connecting rod and
piston assem bly and the cylind er bore to
assure that each assembly is returned to its
original bore.
• R epeat th is pro ced ure on the rem ain in g
connecting rod assemblies.
FLYWHEEL REMOVAL
R em ove or D isconnect (Fig ure 5)
1. Flywheel bolts (66).
2. Flywheel (67).
3. Spacer (68).
CRANKSHAFT REMOVAL
The main bearings and rear oil seal can be replaced
w ithout removing the crankshaft, as outlined later in this
section.
R em ove or D isconnect (Fig ures 5, 18 and 19)
• Check the main bearing caps (124 and 126) location
markings. The main bearing caps are numbered 1
through 5 from the front to the rear of the engine.
The caps must be returned to their original locations
during engine assembly.
1. Crankshaft tim ing gear (87).
Bolts (125).
Main bearing caps (124 and 126).
4. Crankshaft (88). Lift the crankshaft straight up,
taking care to avoid dam age to the crankshaft
journals and thrust flange surfaces.
5. Seal (71).
6. Main bearing inserts (figure 19).
• If the main bearing inserts are to be reused,
mark them to insure they are installed in their
original positions before removal.
2.
3.
Summary of Contents for 1989 Light Duty Truck
